DEA-5TT1 Exam Dumps Update – Study Materials Valid For The Associate – Networking Exam

On By passitdump

The updated version of the DEA-5TT1 exam dumps you want here. If you want Associate – Networking exam study materials, here’s what you want. Passitdump provides you with the best DEA-5TT1 exam dumps and DEA-5TT1 study materials to help you prepare for the exam.

With the Passitdump DEA-5TT1 exam dumps you can successfully pass the difficult Associate-Networking exam.

You can check out the DEA-5TT1 free dumps first and experience the following questions

Question 1:

Which option is used to configure Network Address Translation (NAT) to provide one-to-one mapping between local and global addresses?

A. Outside source static

B. Overload

C. Inside source static

D. PAT

 

Correct Answer: C

Question 2:

At which layer of the OSI model is the Rapid Spanning Tree protocol used to prevent switching loops?

A. Physical

B. Network

C. Data Link

D. Transport

 

Correct Answer: C

Question 3:

Which field of the 802.3 frame is used by network interface cards to synchronize their receivers?

A. Start frame delimiter

B. Preamble

C. Cyclic redundancy check

D. Frame check sequence

 

Correct Answer: B

Question 4:

Which Layer 1 device can be used to enlarge the area covered by a single LAN segment?

A. Router

B. Repeater

C. Switch

D. NIC

 

Correct Answer: B

Question 5:

What accurately describes the Simple Network Time Protocol (SNTP)?

A. Time synchronization algorithms are more complex and account for clock drift.

B. Client makes sudden changes in time to keep synchronized.

C. Client synchronizes among a set of distributed time servers.

D. Implemented on a Dell EMC Network OS 9 and OS 10.

 

Correct Answer: D

Question 6:

Which criteria is used to define an extended MAC ACL filter?

A. Destination MAC address and Ethernet frame type

B. Ethernet frame type and frame size

C. Destination TCP port number and source MAC address

D. Source and destination MAC addresses

 

Correct Answer: D

Question 7:

Which IPv4 address is in the same network as the IP address 182.15.24.40/23 and assignable to a host device?

A. 182.15.23.224

B. 182.15.25.0

C. 182.15.25.255

D. 182.15.26.10

 

Correct Answer: B

Question 8:

Which BASE-T Ethernet standard specifies a CAT6 cable type?

A. 2.5GBASE-T

B. 5GBASE-T

C. 10BASE-T

D. 10GBASE-T

 

Correct Answer: D

Question 9:

A network administrator created three VLANs on an Ethernet switch. How many broadcast domains are created by the switch?

A. 1

B. 2

C. 3

D. 4

 

Correct Answer: C

Question 10:

Refer to the exhibit.

Switch A and Switch B are connected to each other. Both switches use interfaces Gi1/0/1 and Gi1/0/2. Switch A has a Spanning Tree priority of 8192 and Switch B has the default priority. Which interface becomes the root port?

A. Switch A Gi1/0/1

B. Switch A Gi1/0/2

C. Switch B Gi1/0/1

D. Switch B Gi1/0/2

 

Correct Answer: A

Question 11:

You recently joined a company as a junior-level network administrator. You have been tasked with designing the IPv4 scheme for five networks that will be used for training classrooms. These networks need to support no more than 28 devices each. Due to the existing network design, the senior-level network administrator has asked you to work on network 192.168.40.0/24.

If all networks must be made to logically start with the lowest numbered network and end with the largest numbered network, what is the network ID for the third network?

A. 192.168.40.32/27

B. 192.168.40.64/27

C. 192.168.40.96/27

D. 192.168.40.128/27

 

Correct Answer: B

Question 12:

On which Dell EMC Networking switches can Multi-Chassis Link Aggregation (MLAG) be configured?

A. C9000 Series

B. N-Series

C. S-Series

D. Z-Series

 

Correct Answer: B

Question 13:

What is the default OSPF “hello interval”?

A. 5 seconds

B. 10 seconds

C. 15 seconds

D. 30 seconds

 

Correct Answer: B

Question 14:

When configuring a switch, which CLI mode only supports limited show commands?

A. EXEC

B. Maintenance

C. Configuration

D. EXEC Privilege

 

Correct Answer: A

Reference: https://www.dell.com/support/manuals/us/en/04/poweredge-fx2/dell fn ioa% 20config_9.8.0.0_pub-v1/cli-modes?guid=guid-aeb7d44d-2413-4da8-b8b9-2f8a26bad435andlang=en-us

Question 15:

A Dell EMC Networking N-Series switch is configured on a port channel with LACP using the interfaces Te1/0/1 and Te1/0/2. How is the egress traffic distributed among the interfaces?

A. Traffic overflow will be sent to the second interface

B. Interfaces will be used in active/passive

C. Load balanced per packet using round robin

D. Load balanced using a hash function

 

Correct Answer: D