HPE0-J50 Exam Dumps | Newly Updated HP HPE0-J50 Exam Material
The PassITDump HPE0-J50 exam dumps are newly released and are the most effective HPE0-J50 exam material to help you easily pass the Integer Protected HPE Storage Solutions exam.
If you are preparing for the HPE0-J50 exam, the latest update of hpe0-J50 dumps exam materials is essential. With it, you will better study the content of the exam and master all the knowledge points of the exam. These are very helpful in passing the HPE0-J50 exam.
HPE0-J50 free dumps are questions from the latest full HPE0-J50 dumps. Check HPE0-J50 free questions to get a better understanding of HPE0-J50 exams.
Question 1:
Refer to the exhibit.
The administrator has presented an HPE 3PAR StoreServer virtual volume to a server. A single virtual volume is seen as two different offline disks on a Windows 2012 R2 server. What must be done to correct the issue?
A. Install HPE 3PAR DSM MPIO and reboot the server.
B. Install the latest HBA driver and reboot the server.
C. Install the MPIO feature and reboot the server.
D. Install 3PAR host explorer and start service.
Correct Answer: A
Reference: https://assets.ext.hpe.com/is/content/hpedam/documents/4aa5-5000-5999/4aa5-5894/4aa5-5894enw.pdf (21)
Question 2:
Refer to the exhibit.
Which port can be used to connect the HPE MSA 2040 controller to hosts?
A. 4
B. 5
C. 6
D. 8
Correct Answer: A
Reference: https://support.hpe.com/hpsc/doc/public/display?docId=c03792322 (10)
Question 3:
A storage integrator is planning an HPE StoreVirtual VSA installation. Which network-related information may be needed for the implementation?
A. DHCP reservation for virtual IP address of the StoreVirtual cluster
B. jumbo frames need to be enabled for iSCSI traffic
C. flow-control needs to be disabled when using 10Gb NICs
D. virtual IP address for the StoreVirtual cluster
Correct Answer: D
Reference: https://support.hpe.com/hpsc/doc/public/display?docId=c05049837 (4)
Question 4:
A storage integrator has connected a new Windows Server 2012 host to a customer\’s fabric where five HPE 3PAR StoreServ arrays are already installed. The integrator plans to create a script to send the information about the new host to all HPE 3PAR arrays in an automated way.
Which Host Explorer command should be used?
A. tpdhostget status
B. hostagent set
C. tpdhostagent push
D. hostagent list
Correct Answer: C
Reference: https://h20195.www2.hpe.com/v2/GetPDF.aspx/4AA4-4524ENW.pdf (12)
Question 5:
A customer currently utilizing HPE 3PAR StoreServ 7200 is experiencing performance bottlenecks within their SAN storage.
Which cost-effective upsell or cross-sell HPE storage solution will offer significantly more performance and higher capacity to meet their needs and fit within their current infrastructure?
A. HPE 3PAR StoreServ File Controller v3 System
B. HPE 3PAR StoreServ 8440
C. 8-node HPE 3PAR StoreServ 20000 Storage
D. HPE StoreVirtual 3200 Storage
Correct Answer: C
Question 6:
A storage integrator has installed HPE OneView for vCenter to integrate HPE MSA 1040 management from a vSphere Web Client. Which typical configuration task is required after the installation of HPE OneView for vCenter?
A. license HPE OneView for VMware Storage Component
B. register HPE OneView for vCenter to Storage Management Utility
C. add HPE MSA Storage System to vCenter server
D. add vCenter server to HPE OneView for vCenter
Correct Answer: A
Reference: https://support.hpe.com/hpsc/doc/public/display?docId=a00037524en_us
Question 7:
A storage integrator has connected a new Windows Server 2008 R2 host to an HPE 3PAR StoreServ array. After creating a new 3PAR Virtual Volume and exporting it to the new host, the Disk Management tool on the host is displaying two new drives.
Which additional software should the technician install to consolidate the displayed drive?
A. Storage Spaces
B. Enhanced Storage
C. File and Storage Services
D. Multipath I/O feature
Correct Answer: D
Question 8:
A customer has two HPE StoreVirtual VSA instances installed on VMware vSphere hosts, 3TB of data allocated for both with 4TB VSA license. The customer has purchased an HPE StoreVirtual VSA 2014 Software Upgrade 4TB to 10TB upgrade license. The data store size is increased from 3TB to 10.5TB for both VMware servers.
What is required to make the newly-added capacity available? (Choose two.)
A. The VSA appliance needs to be restarted to rescan added storage and expand VSA RAID with the new capacity.
B. The upgrade license requires that the VSA appliance is redeployed.
C. The integrator must remove the current RAID configuration and create a new one after adding more storage to the VSA appliance.
D. The VSA virtual appliance requires more memory and cpu resources.
E. The VMware vmdk file needs to be extended from 3TB to 10TB for each VSA appliance. Then, VSA will detect the additional storage.
Correct Answer: BE
Reference: https://h20195.www2.hpe.com/v2/GetPDF.aspx/c04111621.pdf
Question 9:
When is write throttling of HDDs invoked?
A. to synchronize speed of writing to multiple solid-state drives combined with rotational drives
B. to synchronize speed of writing to multiple solid-state drives
C. when drive wearing rate will cause the drive to fail before the warrantied time
D. when the power consumption of a drive exceeds the power cap
Correct Answer: C
Reference: https://pdfs.semanticscholar.org/c078/528cdf6369cbb01881b8795d44bf799c7490.pdf
Question 10:
Refer to the exhibit.
A storage integrator is creating a virtual volume on an HPE 3PAR StoreServ storage system and plans to create clones of the volume in the future.
Which additional steps will be required for this? (Choose two.)
A. Check Edit additional settings.
B. Configure a new Virtual Domain.
C. Check Enable clones.
D. Check Advanced options.
E. Configure Copy CPG.
Correct Answer: DE
Question 11:
A storage integrator is planning an HPE MSA Storage installation.
What needs to be taken into consideration when implementing a SAS connected model?
A. SAS expander or a SAS switch is supported only with non-redundant paths.
B. SAS expander or a SAS switch is required if eight or more servers are connected.
C. Up to four servers with redundant paths can be connected.
D. Up to four servers with non-redundant paths can be connected.
Correct Answer: C
Reference: https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-a00028199en_usanddocLocale=en_US#N10010
Question 12:
In which areas in SSMC can a 3PAR virtual domain membership be selected? (Choose two.)
A. iSCSI port
B. Host
C. Fibre Channel port
D. StoreServ report
E. Common Provisioning Group
Correct Answer: BD
Question 13:
A storage administrator has deployed a Windows 2012 R2 server which needs to have a virtual volume exported from an HPE StoreServ 8200. After zoning the host to storage and installing the HPE 3PAR Host Explorer on the server, the administrator is not seeing the server name in SSMC host list when creating a host object.
What are two valid options to correct the issue? (Choose two.)
A. Enable host explorer discovery from the HPE 3PAR CLI.
B. Execute tpdhostagent push.
C. Restart the Host Explorer service.
D. Reinstall the Host Explorer service.
E. Restart the SSMC service.
Correct Answer: AB
Question 14:
A storage integrator is handing over an installed HPE 3PAR storage system to a customer. The customer wants the original license key of the system for setlicense command that is used to prevent the system from prompting for confirmation of new license key.
Which of the following command shows original license key?
A. showlicense -raw
B. displaylicense
C. licshow
D. licenseshow
Correct Answer: A
Reference: https://support.hpe.com/hpsc/doc/public/display?docId=c04204279
Question 15:
An HPE StoreVirtual 3200 solution specifies 802.3ad (LACP) bonding is required for the network interfaces. What must be considered when implementing this solution?
A. Only one of the chosen network interfaces will actively pass traffic.
B. The network interfaces chosen may operate at the different speeds.
C. Additional switch configuration will be necessary.
D. The network interfaces chosen must be cabled to different switches.
Correct Answer: C
HPE StoreVirtual 3200 provides three options for the teaming/bonding of the network ports on each storage controller–Active-Passive, Link Aggregation Dynamic Mode (LACP), or Adaptive Load Balancing (ALB) bonding. The simplest solution, the Active-Passive bonding, utilizes only one of the available network ports per controller. The most complex solution, the LACP (802.3ad) bonding, delivers bandwidth aggregation and redundancy across both controller network ports but requires additional switch configurations such as IRF trunking. The preferred and recommended bonding mode is ALB, where the network ports may be connected to different switches, therefore, support switch failover.